FuriousFPV LR1000D Mini Receiver for Frsky

Furious FPV LR1000D Diversity Range Anxiety Nullified
Micron light with an ultra compact footprint, The Furious FPV LR1000 takes receiver technology to new worlds with the range to make it work. The range, you Micron light with an ultra compact footprint, The Furious FPV LR1000D takes receiver technology to new worlds with the range to make it work. The range, you asked? One Full Kilometer. That's over a half mile for you imperial guys & gals.

The LR1000D doesn't stop short with range, though - not a chance. With feature packed brilliance, Furious FPV brings amazing FPV goodness with an S-bus output without inverter, (8) channels of output, a 9th channel dedicated to RSSI, telemetry hub, and full compatibility with FrSky Taranis, Taranis Plus, & XJT Module.

Designed for ultra tight spaces with a keen eye on light weight, the LR1000D is the ultimate Rx solution that allows the freedom of flight without fear of Tx drop out. Simply put, you can push the boundaries of range with the full knowledge the LR1000D will be listening intently as you explore new worlds of FPV.

Features:

• 1kM Far Reaching Range
• 2.2g Ultra Light Weight Layout
• Incredibly Compact for Tight Installs
• S-bus Compatibility w/ No FC Inverter Necessary
• (8) Channels of Output w/ 9th Channel Dedicated to RSSI
• Ultra Rapid 0.1s Telemetry Hub Update Rate
• FrSky Compatible, Including Taranis, Taranis Plus & XJT Module

Specifications :

• Range: 1kM
• Input Voltage Range: 3.5V - 10.0V (5V Normal Operating Range)
• Weight: 2.2g
• Size: 24.5mm x 14mm x 4mm
• Compatibility: FrSky Taranis, Taranis Plus & XJT

1. Binding the receiver to the Frsky Taranis X9D

• In the Taranis, go to MODE SETUP (page 2) in the model configuration.
• Go to Mode inside Internal RF and select D8.
• Press and hold the receiver bind button and plug your battery in to turn the receiver on.
• Release the button. A green LED lights up in the receiver.
• Going back to the Taranis; we press BIND. The transmitter beeps, indicating it’s in bind mode.
• Wait for the green LED on the receiver to turn off. The binding procedure has finished.
• Exit the BIND mode in the Taranis.
• Unplug the battery to turn off the receiver.
  
  

2. Binding the receiver to the XJT module

• Using the dip switches of the XJT module, select the D8 mode. They shoud be in the following position: switch 1 = ON, switch 2 = OFF.
• Press and hold the receiver bind button and plug your battery in to turn the receiver on.
• Release the button. A green LED lights up in the receiver.
• Press and hold the bind button and turn the transmitter on.
• Release the button. A green light shoud blink in the module, indicating it’s in bind mode.
• Wait for the green LED on the receiver to turn off. The binding procedure has finished.
• Turn the transmitter off.
• Unplug the battery to turn off the receiver.
  
  

3. Receiver Configuration in the Cleanflight configurator

• In the PORTS tab, select the UART that corresponds to the receiver (usually UART3 in F3 flight controllers) and activate Serial RX.
• Save by clicking on the Save and Reboot button.
• In the CONFIGURATION tab, in the Receiver Mode section, select RX_SERIAL.
• In the same tab, in the Serial Receiver Provider section, select SBUS.
• Save by clicking on the Save and Reboot button.
• Go to CLI and type the following commands:
  set sbus_inversion = OFF
  save
  The FC will reboot, applying the change.
• Go to the RECEIVER tab and make sure the receiver acts like it should.

4. Telemetry Configuration:

• In the PORTS tab, select the UART that corresponds to the telemetry (usually UART2 in F3 flight controllers) and select FrSky in Telemetry. Leave the baudrate to AUTO.
• Go to CLI, and type the following commands:
  set telemetry_inversion = ON
  save
  The FC will reboot, applying the change.
• Make sure you’re getting thetelemetry values in our Taranis correctly.