Matek F405-CTR Flight Controller

Matek F405-CTR Flight Controller

生產商: Matek
This is the All-in-one F4 FC by Matek, combing a F405 FC and PDB together, built-in Baro sensor, BetaFlight OSD, BEC 5V/2A, SD card slot for Blackbox and current sensor....

有現貨

HK$350.00 HK$357.00
This is the All-in-one F4 FC by Matek, combing a F405 FC and PDB together, built-in Baro sensor, BetaFlight OSD, BEC 5V/2A, SD card slot for Blackbox and current sensor.

FC Specifications
  • Target : MATEKF405
  • MCU : 168MHz STM32F405
  • IMU : MPU6000 accelerometer/gyro (SPI)
  • Baro : BMP280 (I2C)
  • OSD : BetaFlight OSD w/ AT7456E chip
  • Blackbox : MicroSD card slot (SD/SDHC)
  • VCP, UART1, UART2, UART3, UART4, UART5
  • Built in inverter for SBUS input (UART2-RX)
  • PPM/UART Shared : UART2-RX
  • SoftSerial on TX2, S5 or S6 optional
  • Camera control on S6 or DAC optional
  • Smartaudio & Tramp VTX protocol supported
  • WS2812 Led Strip : Yes
  • Beeper : Yes
  • RSSI : Yes
* If Gyro 32kHz & PID loop 16kHz, Blackbox logging rate 1kHz Max.

PDB Specifications
  • Input : 9~27V (3~6S LiPo) w/TVS protection
  • PDB : 4x30A (Max.4x50A), 6 layers*2oz copper PCB
  • BEC : 5V/2A (Max. 3A)
  • LDO 3.3V : Max.300mA for Spektrum RX
  • Current Sensor 200A (Scale 165)
  • Battery Voltage Sensor : 1:10 (Scale 110)
General Specifications
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • 6x PWM / DShot outputs without conflict
  • 5x UARTs
  • 1x Group of G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
  • 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
  • 1x pair I2C1 pads
  • 1x Side-press button for BOOT(DFU) mode
  • 36x46mm PCB with 30.5mm mounting holes
  • 10g







Wiring diagram (Click to enlarge)


BetaFlight Pins Definition
Pad/Hole PIN TIM Resource option
PPM PA3 TIM5_CH4
S1 PC6 TIM3_CH1
S2 PC7 TIM8_CH2
S3 PC8 TIM8_CH3
S4 PC9 TIM8_CH4
S5 PA15 TIM2_CH1 LED_STRIP, serial_tx 11
S6 PA8 TIM1_CH1 camera_control
2812 LED Strip PB6 TIM4_CH1
TX4 PA0 TIM5_CH1 serial_tx 12 (BF3.2.3)
RX4 PA1 TIM5_CH2 serial_rx 12 (BF3.2.3)
TX2 PA2 TIM9_CH1 serial_tx 11 (BF3.2.3)
DAC PA4 camera_control (BF3.3)


  • S5 (PA15) or TX2 (PA2) can be resourced to softserial for Frsky SmartPort
  • 2812LED_Strip share I2C1_SCL pad as default. either enable LED_Strip, or enable Baro.
  • 2812LED can be resourced to S5 (PA15) if using Baro the same time with BF firmware
  • S6 pad (PA8) can be resourced to Camera Control

    • CLI command :
    resource motor 5 none
    resource led_strip A15
    resource motor 6 none
    resource camera_control A08
    resource serial_tx 11 A02
    save
    Includes
    • w/ 1x Rubycon ZLH 35V/470uF (Low ESR)
    • w/ 6x silicon grommets M4 to M3
    • w/ 1x FR4 PCB Plate 36*36*1mm

    Best Sellers