Matek F405-STD Flight Controller
生產商: Matek
This is the standard F4 flight controller by Matek, combing a F405 FC and OSD module together, made to work with Matek FCHUB-6S / FCHUB-VTX / FCHUB-W (* sold separately)....
有現貨

This is the standard F4 flight controller by Matek, combing a F405 FC and OSD module together, made to work with Matek FCHUB-6S / FCHUB-VTX / FCHUB-W (* sold separately). The F405-STD has built-in Baro sensor, BetaFlight OSD and SD card slot for Blackbox.
FC Specifications
General Specifications



Wiring diagram (Click to enlarge)

BetaFlight Pins Definition
S5 (PA15) , S6(PA8) or TX2 (PA2) can be resourced to softserial for Frsky SmartPort
2812LED_Strip share I2C1_SCL pad as default. either enable LED_Strip, or enable Baro.
2812LED can be resourced to S7 (PB8) if using Baro the same time with BF firmware
S5 (PA15) or S6 pad (PA8) can be resourced to Camera Control
FC Specifications
- Target : MATEKF405
- MCU: 168MHz STM32F405RGT6
- IMU: 32K ICM20602 gyro/accelerometer (SPI)
- Baro: BMP280 (I2C)
- OSD: BetaFlight OSD w/ AT7456E chip
- Blackbox: MicroSD card slot (SD/SDHC)
- VCP, UART1, UART2, UART3, UART4, UART5
- Built in inverter for SBUS input (UART2-RX)
- PPM/UART Shared: UART2-RX
- SoftSerial on TX2, S5 or S6 optional
- Camera control on S6 or DAC optional
- Smartaudio & Tramp VTX protocol supported
- Battery Voltage Sensor: 1:10
- Current Sensor: No (use with FCHUB-6S, FCHUB-VTX, FCHUB-W, sold separately)
- BEC 5V: No (use with FCHUB-6S, FCHUB-VTX, FCHUB-W sold separately)
- LDO 3.3V: Max.300mA
- I2C1 SDA & SCL: Yes
- WS2812 Led Strip : Yes
- Beeper : Yes
- RSSI: Yes
General Specifications
- 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
- 6x PWM / DShot outputs without conflict
- 2x 2812LED outputs option
- 5x UARTs
- 1x Group of 5V/G/S1/S2/S3/S4 pads for 4in1 ESC Signal/GND
- 4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)
- 1x pair I2C1 pads
- 1x Side-press button for BOOT(DFU) mode
- 1x 16pin bottom mounted FFC Slot for FCHUB-6S, FCHUB-VTX or FCHUB-W connection
- 36x36mm PCB with 30.5mm mounting holes



Wiring diagram (Click to enlarge)

BetaFlight Pins Definition
Pad/Hole | PIN | TIM | Resource option |
PPM | PA3 | TIM5_CH4 | |
S1 | PC6 | TIM3_CH1 | |
S2 | PC7 | TIM8_CH2 | |
S3 | PC8 | TIM8_CH3 | |
S4 | PC9 | TIM8_CH4 | |
S5 | PA15 | TIM2_CH1 | serial_tx 11, camera_control |
S6 | PA8 | TIM1_CH1 | serial_tx 11, camera_control |
2812 LED Strip | PB6 | TIM4_CH1 | |
S7 | PB8 | TIM4_CH3 | LED_STRIP |
TX4 | PA0 | TIM5_CH1 | serial_tx 12 (BF3.2.3) |
RX4 | PA1 | TIM5_CH2 | serial_rx 12 (BF3.2.3) |
TX2 | PA2 | TIM9_CH1 | serial_tx 11 (BF3.2.3) |
DAC | PA4 | camera_control (BF3.3) |
resource motor 5 none
resource serial_tx 11 A15
resource motor 6 none
resource camera_control A08
resource motor 7 none
resource led_strip 1 B08
save
Includesresource serial_tx 11 A15
resource motor 6 none
resource camera_control A08
resource motor 7 none
resource led_strip 1 B08
save
- w/ 2x 0.5mm*16Pin 5cm Flexible Flat Cable
- w/ 4pcs M3 Anti-vibration Standoffs